Ubuntu no WLAN

Post Reply
andre
Posts: 5
Joined: Sat Sep 26, 2009 5:15 pm

Ubuntu no WLAN

Post by andre »

Hi there,

since 2 days im trying to get my wlan working under ubuntu. I always get
the same error : "authentication on ap timed out". I can see the
network, but i cant connect. Tried WPA, WEP.

So here is my story :

Started 9.04 LiveCD from USB. Wlan works.
Installed 9.04 on another USB and bootet the new installation. Wlan works.
Installed "Kernel related stuff" and the other drivers. Wlan timed out.
Replaced the Gnomestuff against Wicd. Wlan timed out.

Started 8.04 LTS from USB. No Wlan.
Installed 8.04 on another USB and bootet the new installation. No Wlan.
Installed "Kernel related stuff" and the other drivers. Now wlan exists,
but timed out.
Replaced the Gnomestuff against Wicd. Wlan timed out.

I have no idea whats wrong. In both cases i have used the install
instructions from the wiki.

Anyone can help ?

Thanks in advance.

Andre

andre
Posts: 5
Joined: Sat Sep 26, 2009 5:15 pm

Re: Ubuntu no WLAN

Post by andre »

Its me again. Made some steps forward. I know now that wlan stops after replacing the xorg.conf and reboot. If i replace the "fitpc2-xorg.conf" against the original, wlan works for me (after another boot).

Have no ideo why. Hope this helps someone to explain the problem to me.

Denis
Posts: 301
Joined: Sun Apr 26, 2009 3:24 pm

Re: Ubuntu no WLAN

Post by Denis »

What type of wi-fi card do you have? Post output of

Code: Select all

lspci | grep -i network
Compulab's Linux support

andre
Posts: 5
Joined: Sat Sep 26, 2009 5:15 pm

Re: Ubuntu no WLAN

Post by andre »

Hi Denis,

this command gives no output. I found a manual to start wlan by commandline. Here is the result :

Code: Select all

sudo wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ap_scan=1
ctrl_interface='/var/run/wpa_supplicant'
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=5):
     72 65 61 70 31                                    reap1           
scan_ssid=0 (0x0)
proto: 0x1
key_mgmt: 0x2
PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]

pairwise: 0x8
group: 0x8
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='reap1'
Initializing interface (2) 'wlan0'
Interface wlan0 set UP - waiting a second for the driver to complete initialization
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf flags 0x0
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:12:0e:ad:c3:27
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Added interface wlan0
Ignore event for foreign ifindex 3
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 0 bytes of scan results (0 BSSes)
Cached scan results are empty - not posting
Selecting BSS from priority group 0
Try to find WPA-enabled AP
Try to find non-WPA AP
No suitable AP found.
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 0 bytes of scan results (0 BSSes)
CTRL-EVENT-SCAN-RESULTS 
Selecting BSS from priority group 0
Try to find WPA-enabled AP
Try to find non-WPA AP
No suitable AP found.
Setting scan request: 5 sec 0 usec
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 30 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 312 bytes of scan results (1 BSSes)
CTRL-EVENT-SCAN-RESULTS 
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:12:17:69:45:8c ssid='reap1' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   selected based on WPA IE
   selected WPA AP 00:12:17:69:45:8c ssid='reap1'
Trying to associate with 00:12:17:69:45:8c (SSID='reap1' freq=2472 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_psk
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=12
Authentication with 00:12:17:69:45:8c timed out.
Added BSSID 00:12:17:69:45:8c into blacklist
No keys have been configured - skip key clearing
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 30 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 312 bytes of scan results (1 BSSes)
CTRL-EVENT-SCAN-RESULTS 
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:12:17:69:45:8c ssid='reap1' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   selected based on WPA IE
   selected WPA AP 00:12:17:69:45:8c ssid='reap1'
Trying to associate with 00:12:17:69:45:8c (SSID='reap1' freq=2472 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_psk
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=12
^CCTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Removed BSSID 00:12:17:69:45:8c from blacklist (clear)
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6
reese@robi:~$ 
Maybe this helps ?

Another question: Is it possible to get a complete 9.04 installation (incl. all drivers and of course wlan) as ISO-Image ?

Thanks,

Andre

Denis
Posts: 301
Joined: Sun Apr 26, 2009 3:24 pm

Re: Ubuntu no WLAN

Post by Denis »

No, I do not know about manual you have used. It does not help too much.

First, let`s find out type of wi-fi card you have. Post output of lspci, iwconfig, ifconfig.
Compulab's Linux support

andre
Posts: 5
Joined: Sat Sep 26, 2009 5:15 pm

Re: Ubuntu no WLAN

Post by andre »

Hi Denis,

because in the future i dont want to run x locally, i removed the display driver and the xorg.conf and tried to configure the wlan without network-manager or wicd from commandline. I used wpa_supplicant. The situation is now: i can connect via wpa_supplicant startet from x-terminal, but i cant connect started from tty01 (commandline). In both cases i use exactly the same commands.

Here are the outputs from wpa_supplicant :

TTY01(WLAN is not working)

Code: Select all

Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ap_scan=1
ctrl_interface='/var/run/wpa_supplicant'
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=5):
 	72 65 61 70 31                                	reap1       	
PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]

key_mgmt: 0x2
proto: 0x1
pairwise: 0x8
group: 0x8
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='reap1'
Initializing interface (2) 'wlan0'
Interface wlan0 set UP - waiting a second for the driver to complete initialization
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf flags 0x0
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:12:0e:ad:c3:27
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Added interface wlan0
Ignore event for foreign ifindex 3
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 311 bytes of scan results (1 BSSes)
CTRL-EVENT-SCAN-RESULTS 
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:12:17:69:45:8c ssid='reap1' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   selected based on WPA IE
   selected WPA AP 00:12:17:69:45:8c ssid='reap1'
Trying to associate with 00:12:17:69:45:8c (SSID='reap1' freq=2472 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_psk
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=12
Authentication with 00:12:17:69:45:8c timed out.
Added BSSID 00:12:17:69:45:8c into blacklist
No keys have been configured - skip key clearing
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 30 seconds
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 311 bytes of scan results (1 BSSes)
CTRL-EVENT-SCAN-RESULTS 
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:12:17:69:45:8c ssid='reap1' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   selected based on WPA IE
   selected WPA AP 00:12:17:69:45:8c ssid='reap1'
Trying to associate with 00:12:17:69:45:8c (SSID='reap1' freq=2472 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_psk
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=12
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Removed BSSID 00:12:17:69:45:8c from blacklist (clear)
Cancelling scan request
Cancelling authentication timeout
WEXT: Operstate: linkmode=0, operstate=6
X-Terminal (WLAN is working)

Code: Select all

Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ap_scan=1
ctrl_interface='/var/run/wpa_supplicant'
Line: 4 - start of a new network block
ssid - hexdump_ascii(len=5):
 	72 65 61 70 31                                	reap1       	
PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]

key_mgmt: 0x2
proto: 0x1
pairwise: 0x8
group: 0x8
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='reap1'
Initializing interface (2) 'wlan0'
Interface wlan0 set UP - waiting a second for the driver to complete initialization
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf flags 0x0
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:12:0e:ad:c3:27
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
Added interface wlan0
Ignore event for foreign ifindex 3
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 311 bytes of scan results (1 BSSes)
CTRL-EVENT-SCAN-RESULTS 
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:12:17:69:45:8c ssid='reap1' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   selected based on WPA IE
   selected WPA AP 00:12:17:69:45:8c ssid='reap1'
Trying to associate with 00:12:17:69:45:8c (SSID='reap1' freq=2472 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_psk
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b04 len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b19 len=8
Received 311 bytes of scan results (1 BSSes)
CTRL-EVENT-SCAN-RESULTS 
Selecting BSS from priority group 0
Try to find WPA-enabled AP
0: 00:12:17:69:45:8c ssid='reap1' wpa_ie_len=22 rsn_ie_len=0 caps=0x11
   selected based on WPA IE
   selected WPA AP 00:12:17:69:45:8c ssid='reap1'
Already associated with the selected AP.
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8c02 len=175
WEXT: Custom wireless event: 'ASSOCINFO(ReqIEs=00057265617031010802040b160c12182432043048606cdd160050f20101000050f20201000050f20201000050f202 RespIEs=010882848b962430486c32040c121860dd050010180100)'
Association info event
req_ies - hexdump(len=47): 00 05 72 65 61 70 31 01 08 02 04 0b 16 0c 12 18 24 32 04 30 48 60 6c dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
resp_ies - hexdump(len=23): 01 08 82 84 8b 96 24 30 48 6c 32 04 0c 12 18 60 dd 05 00 10 18 01 00
WPA: set own WPA/RSN IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:12:17:69:45:8c
State: ASSOCIATING -> ASSOCIATED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
Associated to a new BSS: BSSID=00:12:17:69:45:8c
No keys have been configured - skip key clearing
Associated with 00:12:17:69:45:8c
WPA: Association event - clear replay counter
WPA: Clear old PTK
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: enable timer tick
EAPOL: SUPP_BE entering state IDLE
Setting authentication timeout: 10 sec 0 usec
Cancelling scan request
RX EAPOL from 00:12:17:69:45:8c
RX EAPOL - hexdump(len=99): 01 03 00 5f fe 00 89 00 20 00 00 00 00 00 00 00 00 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Setting authentication timeout: 10 sec 0 usec
IEEE 802.1X RX: version=1 type=3 length=95
  EAPOL-Key type=254
  key_info 0x89 (ver=1 keyidx=0 rsvd=0 Pairwise Ack)
  key_length=32 key_data_length=0
  replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_nonce - hexdump(len=32): 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff
  key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
WPA: RX EAPOL-Key - hexdump(len=99): 01 03 00 5f fe 00 89 00 20 00 00 00 00 00 00 00 00 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
State: ASSOCIATED -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 00:12:17:69:45:8c (ver=1)
WPA: Renewed SNonce - hexdump(len=32): dc bb cf ba c1 70 d3 8b 8d 4a c6 f9 37 64 c2 59 17 3d 57 9c b3 97 da d2 98 2e d0 5e c3 f3 0f 8e
WPA: PTK derivation - A1=00:12:0e:ad:c3:27 A2=00:12:17:69:45:8c
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: Sending EAPOL-Key 2/4
WPA: TX EAPOL-Key - hexdump(len=123): 01 03 00 77 fe 01 09 00 20 00 00 00 00 00 00 00 00 dc bb cf ba c1 70 d3 8b 8d 4a c6 f9 37 64 c2 59 17 3d 57 9c b3 97 da d2 98 2e d0 5e c3 f3 0f 8e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 72 15 a1 b6 5d ef 85 f1 80 9f 14 49 25 56 a1 b2 00 18 dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RX EAPOL from 00:12:17:69:45:8c
RX EAPOL - hexdump(len=99): 01 03 00 5f fe 00 89 00 20 00 00 00 00 00 00 00 01 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
IEEE 802.1X RX: version=1 type=3 length=95
  EAPOL-Key type=254
  key_info 0x89 (ver=1 keyidx=0 rsvd=0 Pairwise Ack)
  key_length=32 key_data_length=0
  replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 01
  key_nonce - hexdump(len=32): 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff
  key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
WPA: RX EAPOL-Key - hexdump(len=99): 01 03 00 5f fe 00 89 00 20 00 00 00 00 00 00 00 01 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
WPA: RX message 1 of 4-Way Handshake from 00:12:17:69:45:8c (ver=1)
WPA: PTK derivation - A1=00:12:0e:ad:c3:27 A2=00:12:17:69:45:8c
WPA: PMK - hexdump(len=32): [REMOVED]
WPA: PTK - hexdump(len=64): [REMOVED]
WPA: WPA IE for msg 2/4 - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: Sending EAPOL-Key 2/4
WPA: TX EAPOL-Key - hexdump(len=123): 01 03 00 77 fe 01 09 00 20 00 00 00 00 00 00 00 01 dc bb cf ba c1 70 d3 8b 8d 4a c6 f9 37 64 c2 59 17 3d 57 9c b3 97 da d2 98 2e d0 5e c3 f3 0f 8e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 86 62 47 a6 5b 2a 98 33 9c a5 06 ef 57 bc c8 58 00 18 dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
RX EAPOL from 00:12:17:69:45:8c
RX EAPOL - hexdump(len=123): 01 03 00 77 fe 01 c9 00 20 00 00 00 00 00 00 00 02 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ac b2 2c 4d 65 3d a7 95 c7 bd e3 9b da 54 19 09 00 18 dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
IEEE 802.1X RX: version=1 type=3 length=119
  EAPOL-Key type=254
  key_info 0x1c9 (ver=1 keyidx=0 rsvd=0 Pairwise Install Ack MIC)
  key_length=32 key_data_length=24
  replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 02
  key_nonce - hexdump(len=32): 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff
  key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_mic - hexdump(len=16): ac b2 2c 4d 65 3d a7 95 c7 bd e3 9b da 54 19 09
WPA: RX EAPOL-Key - hexdump(len=123): 01 03 00 77 fe 01 c9 00 20 00 00 00 00 00 00 00 02 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 53 ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ac b2 2c 4d 65 3d a7 95 c7 bd e3 9b da 54 19 09 00 18 dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
WPA: RX message 3 of 4-Way Handshake from 00:12:17:69:45:8c (ver=1)
WPA: IE KeyData - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: Sending EAPOL-Key 4/4
WPA: TX EAPOL-Key - hexdump(len=99): 01 03 00 5f fe 01 09 00 20 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 da 1f 73 c4 1e ac f0 16 55 52 c2 61 71 a9 0d 0a 00 00
WPA: Installing PTK to the driver.
WPA: RSC - hexdump(len=6): 00 00 00 00 00 00
wpa_driver_wext_set_key: alg=2 key_idx=0 set_tx=1 seq_len=6 key_len=32
State: 4WAY_HANDSHAKE -> GROUP_HANDSHAKE
RX EAPOL from 00:12:17:69:45:8c
RX EAPOL - hexdump(len=131): 01 03 00 7f fe 03 91 00 20 00 00 00 00 00 00 00 03 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 51 ff ff af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 54 ff ff 0d 2e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7e 83 dc 16 a4 43 57 3e d0 49 90 19 e5 50 09 c4 00 20 47 ac b0 d7 0d 06 d4 01 b9 58 05 5b 2e d0 57 49 87 46 a1 68 af d3 d8 bf 82 34 8e ad 56 e6 44 5c
IEEE 802.1X RX: version=1 type=3 length=127
  EAPOL-Key type=254
  key_info 0x391 (ver=1 keyidx=1 rsvd=0 Group Ack MIC Secure)
  key_length=32 key_data_length=32
  replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 03
  key_nonce - hexdump(len=32): 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 51 ff ff
  key_iv - hexdump(len=16): af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 54 ff ff
  key_rsc - hexdump(len=8): 0d 2e 00 00 00 00 00 00
  key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
  key_mic - hexdump(len=16): 7e 83 dc 16 a4 43 57 3e d0 49 90 19 e5 50 09 c4
WPA: RX EAPOL-Key - hexdump(len=131): 01 03 00 7f fe 03 91 00 20 00 00 00 00 00 00 00 03 14 f2 d3 1a e3 9b 1d f3 85 14 92 2f 14 35 c5 7b af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 51 ff ff af 9d ee 40 7c 0f 5a ac ee 44 a4 f2 c1 54 ff ff 0d 2e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 7e 83 dc 16 a4 43 57 3e d0 49 90 19 e5 50 09 c4 00 20 47 ac b0 d7 0d 06 d4 01 b9 58 05 5b 2e d0 57 49 87 46 a1 68 af d3 d8 bf 82 34 8e ad 56 e6 44 5c
WPA: RX message 1 of Group Key Handshake from 00:12:17:69:45:8c (ver=1)
State: GROUP_HANDSHAKE -> GROUP_HANDSHAKE
WPA: Group Key - hexdump(len=32): [REMOVED]
WPA: Installing GTK to the driver (keyidx=1 tx=0 len=32).
WPA: RSC - hexdump(len=6): 0d 2e 00 00 00 00
wpa_driver_wext_set_key: alg=2 key_idx=1 set_tx=0 seq_len=6 key_len=32
WPA: Sending EAPOL-Key 2/2
WPA: TX EAPOL-Key - hexdump(len=99): 01 03 00 5f fe 03 11 00 20 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 95 bf f2 23 03 d7 34 2c cd 93 80 61 30 f9 92 00 00
WPA: Key negotiation completed with 00:12:17:69:45:8c [PTK=TKIP GTK=TKIP]
Cancelling authentication timeout
State: GROUP_HANDSHAKE -> COMPLETED
CTRL-EVENT-CONNECTED - Connection to 00:12:17:69:45:8c completed (auth) [id=0 id_str=]
wpa_driver_wext_set_operstate: operstate 0->1 (UP)
WEXT: Operstate: linkmode=-1, operstate=6
EAPOL: External notification - portValid=1
EAPOL: External notification - EAP success=1
EAPOL: SUPP_PAE entering state AUTHENTICATING
EAPOL: SUPP_BE entering state SUCCESS
EAP: EAP entering state DISABLED
EAPOL: SUPP_PAE entering state AUTHENTICATED
EAPOL: SUPP_BE entering state IDLE
EAPOL authentication completed successfully
RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
EAPOL: startWhen --> 0
EAPOL: disable timer tick
^CCTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
State: COMPLETED -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 1->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_deauthenticate
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: No such file or directory
Driver did not support SIOCSIWENCODEEXT
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAPOL: External notification - portValid=0
wpa_driver_wext_set_wpa
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_countermeasures
No keys have been configured - skip key clearing
Cancelling scan request
Cancelling authentication timeout
Here are the outputs you asked for :

Code: Select all

reese@robi:~$ lspci
00:00.0 Host bridge: Intel Corporation System Controller Hub (SCH Poulsbo) (rev 07)
00:02.0 VGA compatible controller: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller (rev 07)
00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller (rev 07)
00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 (rev 07)
00:1d.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 (rev 07)
00:1d.1 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 (rev 07)
00:1d.2 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 (rev 07)
00:1d.7 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 (rev 07)
00:1e.0 SD Host controller: Intel Corporation System Controller Hub (SCH Poulsbo) SDIO Controller #1 (rev 07)
00:1e.1 SD Host controller: Intel Corporation System Controller Hub (SCH Poulsbo) SDIO Controller #2 (rev 07)
00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge (rev 07)
00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller (rev 07)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

Code: Select all

reese@robi:~$ lshw -C network
WARNING: you should run this program as super-user.
  *-network               
       description: Ethernet interface
       product: RTL8111/8168B PCI Express Gigabit Ethernet controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: pci@0000:02:00.0
       logical name: eth0
       version: 02
       serial: 00:01:c0:05:e3:8f
       width: 64 bits
       clock: 33MHz
       capabilities: bus_master cap_list ethernet physical
       configuration: broadcast=yes driver=r8169 driverversion=2.3LK-NAPI ip=192.168.0.19 latency=0 module=r8169 multicast=yes
  *-network:0 DISABLED
       description: Wireless interface
       physical id: 1
       logical name: wlan0
       serial: 00:12:0e:ad:c3:27
       capabilities: ethernet physical wireless
       configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg
  *-network:1 DISABLED
       description: Ethernet interface
       physical id: 2
       logical name: pan0
       serial: 9e:f0:0e:10:5b:34
       capabilities: ethernet physical
       configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A multicast=yes

Code: Select all

reese@robi:~$ iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  no wireless extensions.

wlan0     IEEE 802.11bg  ESSID:""  
          Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated   
          Tx-Power=0 dBm   
          Retry min limit:7   RTS thr:off   Fragment thr=2352 B   
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

pan0      no wireless extensions.

Code: Select all

reese@robi:~$ ifconfig
eth0      Link encap:Ethernet  Hardware Adresse 00:01:c0:05:e3:8f  
          inet Adresse:192.168.0.19  Bcast:192.168.0.255  Maske:255.255.255.0
          inet6-Adresse: fe80::201:c0ff:fe05:e38f/64 Gültigkeitsbereich:Verbindung
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metrik:1
          RX packets:3834 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2920 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:1000 
          RX bytes:292331 (292.3 KB)  TX bytes:374439 (374.4 KB)
          Interrupt:7 Basisadresse:0x8000 

lo        Link encap:Lokale Schleife  
          inet Adresse:127.0.0.1  Maske:255.0.0.0
          inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
          UP LOOPBACK RUNNING  MTU:16436  Metrik:1
          RX packets:130 errors:0 dropped:0 overruns:0 frame:0
          TX packets:130 errors:0 dropped:0 overruns:0 carrier:0
          Kollisionen:0 Sendewarteschlangenlänge:0 
          RX bytes:20058 (20.0 KB)  TX bytes:20058 (20.0 KB)
Thank you,

Andre

Post Reply

Return to “Ubuntu 8.04”