FACE Modules:FM-VC

From fit-PC wiki
Revision as of 14:24, 8 September 2015 by Maxim (Talk | contribs) (Cables)

Jump to: navigation, search

FM-VC Module

FM-VC FACE Module provide the ability for Video and Audio real and non-real time capture from low cost analog video sensors. Features A/V sampling, video, image processing and motion detection algorithms. In addition to application specific capabilities FM-VC offers several general purpose connectivity options as dual USB2.0 downstream ports and serial port supporting either single ended RS232 or differential mode RS485/RS422 operation.
FM-VC FACE Module designed for surveillance, homeland security and any other video analytic system.

Refer to Compatibility Matrix for products fit.

Highlights

  • 8x Real time capture Composite Analog Video NTSC/PAL/SECAM channels
  • 16x Non-real time capture Composite Analog Video NTSC/PAL/SECAM channels
  • 8x Real time capture Analog Audio channels
  • 2x DB15 female connectors for AV capture
  • 2x USB2.0 downstream ports, up to 480Mbps half-duplex
  • 1x Serial port supporting RS232/RS422/RS488 communication via RJ11

Block Diagram

FM-VC.png


Hardware Specifications

The following section provides information about FM-VC main components and features.

Intersil TW6869 Video Decoder The TW6869 is a highly integrated solution that supports multi-channel video and audio capture via PCI Express x1 interface for PC DVR system and video analytic application. It contains high quality eight channel NTSC/PAL/SECAM video decoders that convert analog composite video signal to digital component YCbCr data. Adaptive 4H comb filter for separating luminance and chrominance to reduce cross noise artifacts.
TW6869 contains a high performance proprietary DMA controller that fully optimizes the utilization of PCI Express x1 bandwidth and enables it to transfer video and audio data at a high throughput rate that closely approaches the theoretical limit of PCI Express x1 interface. TW6869 is able to simultaneously decode and transfer 8 real time video streams, or up to 16 channel non-real time video streams in FM-VC application, plus 8 real time audio channel.

Video Decoder Features

  • Accepts all NTSC(M/N/4.43) / PAL(B/D/G/H/I/K/L/M/N/60) standards with auto detection
  • Integrated eight video analog anti-alias filters and 10-bit CMOS ADCs
  • Color Transient Improvement, White peak AGC control
  • Programmable hue, saturation, contrast, brightness and sharpness
  • High quality proprietary fast video locking system for non-real-time application
  • High performance adaptive 4H comb filters for all NTSC and PAL standards

Audio Codec Features

  • Integrated eight audio ADCs
  • 8/16 bit audio word length
  • Sample audio with 8/16/32/44.1/48kHz

DMA Controller

  • Highly-efficient DMA design can support up to 8 real time D1 video and 8 real time audio channels, or up to 32 non-real- time video with optimization of full PCIe x1 bandwidth
  • Multiple digital video format outputs: UYVY/Y422, YUYV/YUY2, IYU1/Y411, Y41P, YUV420, RGB555 and RGB565
  • Integrated internal video and audio generator simplifies system test and development
  • Built-in motion detection engine for each video channel

Host Interface

  • PCI Express Base Specification 1.1 and 2.0 Compliant


SMSC SIO1007 Super-IO Controller The SMSC SIO1007 is PC 99 and ACPI 1.0 compliant Super I/O Controller. The SIO1007 implements the LPC interface with the LPC PortSwitch interface. The LPC PortSwitch interface is a hot switchable external docking LPC interface. It also features a full 16bit internally decoded address bus, a Serial IRQ interface with PCI clock support, relocatable configuration ports and three DMA channel options. The part also includes 16 GPIO pins. The SIO1007 incorporates one complete 8-pin UART. In addition SIO1007 provides a second UART to support a serial Infrared interface that complies with IrDA v1.2 (Fast IR) and several other popular IR formats. Main Features

  • One full function Serial port
  • High Speed UART with Send/Receive 16-Byte FIFOs
  • Support 230k and 460k Baud rates
  • Programmable baud rate generator
  • Modem control circuit
  • IR communication controller
  • LPC bus Host interface
  • LPC PortSwitch interface
  • Two IRQ input pins
  • PC99a and ACPI 1.0 Compliant
  • Intelligent Auto Power Management
  • 16x GPIOs

IDT ICS9DB102 1-to-2 Differential Clock Driver IDT ICS9DB102 is two output clock buffer for PCIe Gen1 & Gen2 with HCSL current mode differential outputs. Device zero-delay buffer supports PCI Express clocking requirements. The ICS9DB102 is driven by a differential compliant input clock. It attenuates jitter on the input clock and has a selectable PLL Band Width to maximize performance in systems with or without Spread-Spectrum clocking.

MAX3221 RS232 Transceiver

  • Single-channel RS232 serial protocol transceiver
  • Implementation RS232 PHY serial protocol port
  • Data rate of 250kbps or more
  • Low power operation and auto-shutdown

ADM3491 RS422/RS485 Transceiver

  • Single-channel RS422/RS485 serial protocol transceiver
  • Implements RS422/RS485 PHY serial protocol
  • Supports full-duplex RS485 protocol with data rate of up to 10Mbps
  • Low power operation and auto-shutdown


DB15 Connector Pinout

Pin # Type Functionality Cable Connector*
P1
P1 - 1 Analog Input Audio 1 AI01
P1 - 2 Analog Input Audio 2 AI02
P1 - 3 - GND
P1 - 4 Analog Input Audio 3 AI03
P1 - 5 Analog Input Audio 4 AI04
P1 - 6 Analog Input Video 1A VI11
P1 - 7 Analog Input Video 2D VI12
P1 - 8 - GND
P1 - 9 Analog Input Video 3A VI13
P1 - 10 Analog Input Video 4D VI14
P1 - 11 Analog Input Video 1B VI21
P1 - 12 Analog Input Video 2C VI22
P1 - 13 - GND
P1 - 14 Analog Input Video 3B VI23
P1 - 15 Analog Input Video 4C VI24
P2
P2 - 1 Analog Input Audio 5 AI01
P2 - 2 Analog Input Audio 6 AI02
P2 - 3 - GND
P2 - 4 Analog Input Audio 7 AI03
P2 - 5 Analog Input Audio 8 AI04
P2 - 6 Analog Input Video 5D VI11
P2 - 7 Analog Input Video 6A VI12
P2 - 8 - GND
P2 - 9 Analog Input Video 7D VI13
P2 - 10 Analog Input Video 8A VI14
P2 - 11 Analog Input Video 5C VI21
P2 - 12 Analog Input Video 6B VI22
P2 - 13 - GND
P2 - 14 Analog Input Video 7C VI23
P2 - 15 Analog Input Video 8B VI24


RJ11 Connector Pinout RJ11 connector serial port pinout shown below. It can function as RS232 or as RS422/RS485. The FM-VC is supplied with a cable for serial RJ11 port.

RS232 RS485
Pin # Type Functionality Type Functionality
1 NC HIGH Z O TX-
2 - GND - GND
3 O TX O TX+
4 I RX I RX+
5 - GND - GND
6 NC HIGH Z I RX-


Cables

The FM-VC is supplied with two DB15 to RCA and BNC cables, along with one RJ11 serial communication cable.

DB15 to RCA and BNC Cables In order to connect the FM-VC to video/audio source, it is provided with two identical cables of DB15-male to 8 BNC and 4 RCA connectors:

  • 4 blue female BNC connectors for analog video input
  • 4 green female BNC connectors for analog video input
  • 4 red female RCA connectors for analog audio input

The signals and the matching connectors of the DB15 to RCA and BNC Cables are detailed in the table below. Signal names are labeled on the cables.

DB15 to RCA and BNC Cable

Signal Name DB15 Pin # Functionality Type Connector Color
VI11 6 Video input BNC Blue
VI12 7 Video input BNC Blue
VI13 9 Video input BNC Blue
VI14 10 Video input BNC Blue
VI21 11 Video input BNC Green
VI22 12 Video input BNC Green
VI23 14 Video input BNC Green
VI24 15 Video input BNC Green
AI01 1 Audio input RCA Red
AI02 2 Audio input RCA Red
AI03 4 Audio input RCA Red
AI04 5 Audio input RCA Red


RJ11 to DB9 Cable The FM-VC is supplied with a RJ11 6P6C-male to DB9-female cable. This cable is compatible with RS232 standard rather with RS485/RS422 DB9 connector standard.

Schematics

Layout

Mechanics

Assembly

Operation Instructions

SW Drivers

  • Note: FM-VC is not operational with 64-bit versions of Windows