Difference between revisions of "IPC2B: USB3.0 Driver Installation Guide"

From fit-PC wiki
Jump to: navigation, search
 
(6 intermediate revisions by the same user not shown)
Line 4: Line 4:
 
==Instructions==
 
==Instructions==
 
1. Install the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_Chipset.zip Chipset driver] before the USB3.0 driver
 
1. Install the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_Chipset.zip Chipset driver] before the USB3.0 driver
 +
 
2. Download the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_USB30.zip USB3.0 driver]
 
2. Download the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_USB30.zip USB3.0 driver]
 +
 
3. Extract the downloaded package
 
3. Extract the downloaded package
 +
 
4. Run the '''OfflineSetup32.exe''' file for Windows 7 32bit or the '''OfflineSetup64.exe''' file for Windows 7 64bit
 
4. Run the '''OfflineSetup32.exe''' file for Windows 7 32bit or the '''OfflineSetup64.exe''' file for Windows 7 64bit
 +
 
5. Follow the on-screen instructions
 
5. Follow the on-screen instructions
 +
 
6. At the the end of installation process, reset the unit
 
6. At the the end of installation process, reset the unit
 +
 
7. Enter the BIOS menu by pressing the '''[F2]''' key during boot
 
7. Enter the BIOS menu by pressing the '''[F2]''' key during boot
8. Browse to
+
 
   Advanced
+
8. In the BIOS menu browse as follows:
     South Bridge Configuration
+
   >Advanced
         '''SB USB Config''' Menu.  
+
     >>South Bridge Configuration
        set '''xHCI Mode''' to '''[Enabled]'''
+
         >>'''SB USB Config''' Menu.  
 +
        *set '''xHCI Mode''' to '''[Enabled]'''
 
9. Press the '''[F10]''' key for Save&Exit
 
9. Press the '''[F10]''' key for Save&Exit
10. When Windows bootd up, open the downloaded package
+
 
 +
10. When Windows boots up, open the downloaded package
 +
 
 
11. Run the '''Setup.exe''' file
 
11. Run the '''Setup.exe''' file
 +
 
12. Follow the on-screen instructions
 
12. Follow the on-screen instructions
 +
 
13. At the the end of installation process, reset the unit
 
13. At the the end of installation process, reset the unit
 +
  
 
[[Category:IPC2]]
 
[[Category:IPC2]]
 
[[Category:software]]
 
[[Category:software]]
 
[[Category:Application notes]]
 
[[Category:Application notes]]

Latest revision as of 06:32, 16 October 2018

  • This application note provides a step by step guide to install USB3.0 drivers over Windows 7.
  • Applicable to IPC2-Broadwell machines.

Instructions

1. Install the Chipset driver before the USB3.0 driver

2. Download the USB3.0 driver

3. Extract the downloaded package

4. Run the OfflineSetup32.exe file for Windows 7 32bit or the OfflineSetup64.exe file for Windows 7 64bit

5. Follow the on-screen instructions

6. At the the end of installation process, reset the unit

7. Enter the BIOS menu by pressing the [F2] key during boot

8. In the BIOS menu browse as follows:

  >Advanced
    >>South Bridge Configuration
       >>SB USB Config Menu. 
        *set xHCI Mode to [Enabled]

9. Press the [F10] key for Save&Exit

10. When Windows boots up, open the downloaded package

11. Run the Setup.exe file

12. Follow the on-screen instructions

13. At the the end of installation process, reset the unit