Difference between revisions of "IPC2B: USB3.0 Driver Installation Guide"

From fit-PC wiki
Jump to: navigation, search
Line 3: Line 3:
  
 
==Instructions==
 
==Instructions==
# Install the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_Chipset.zip Chipset driver] before the USB3.0 driver
+
1. Install the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_Chipset.zip Chipset driver] before the USB3.0 driver
# Download the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_USB30.zip USB3.0 driver]
+
2. Download the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_USB30.zip USB3.0 driver]
# Extract the downloaded package
+
3. Extract the downloaded package
# Run the '''OfflineSetup32.exe''' file for Windows 7 32bit or the '''OfflineSetup64.exe''' file for Windows 7 64bit
+
4. Run the '''OfflineSetup32.exe''' file for Windows 7 32bit or the '''OfflineSetup64.exe''' file for Windows 7 64bit
# Follow the on-screen instructions
+
5. Follow the on-screen instructions
# At the the end of installation process, reset the unit
+
6. At the the end of installation process, reset the unit
# Enter the BIOS menu by pressing the '''[F2]''' key during boot
+
7. Enter the BIOS menu by pressing the '''[F2]''' key during boot
# Browse to
+
8. Browse to
Advanced
+
  Advanced
 
     South Bridge Configuration
 
     South Bridge Configuration
         SB USB Config''' Menu.  
+
         '''SB USB Config''' Menu.  
 
         set '''xHCI Mode''' to '''[Enabled]'''
 
         set '''xHCI Mode''' to '''[Enabled]'''
# Press the '''[F10]''' key for Save&Exit
+
9. Press the '''[F10]''' key for Save&Exit
# When Windows bootd up, open the downloaded package
+
10. When Windows bootd up, open the downloaded package
# Run the '''Setup.exe''' file
+
11. Run the '''Setup.exe''' file
# Follow the on-screen instructions
+
12. Follow the on-screen instructions
# At the the end of installation process, reset the unit
+
13. At the the end of installation process, reset the unit
  
 
[[Category:IPC2]]
 
[[Category:IPC2]]
 
[[Category:software]]
 
[[Category:software]]
 
[[Category:Application notes]]
 
[[Category:Application notes]]

Revision as of 13:50, 15 October 2018

  • This application note provides a step by step guide to install USB3.0 drivers over Windows 7.
  • Applicable to IPC2-Broadwell machines.

Instructions

1. Install the Chipset driver before the USB3.0 driver 2. Download the USB3.0 driver 3. Extract the downloaded package 4. Run the OfflineSetup32.exe file for Windows 7 32bit or the OfflineSetup64.exe file for Windows 7 64bit 5. Follow the on-screen instructions 6. At the the end of installation process, reset the unit 7. Enter the BIOS menu by pressing the [F2] key during boot 8. Browse to

  Advanced
    South Bridge Configuration
       SB USB Config Menu. 
       set xHCI Mode to [Enabled]

9. Press the [F10] key for Save&Exit 10. When Windows bootd up, open the downloaded package 11. Run the Setup.exe file 12. Follow the on-screen instructions 13. At the the end of installation process, reset the unit