Difference between revisions of "IPC2B: USB3.0 Driver Installation Guide"

From fit-PC wiki
Jump to: navigation, search
Line 3: Line 3:
  
 
==Instructions==
 
==Instructions==
* Install the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_Chipset.zip Chipset driver] driver before the USB3.0 driver
+
# Install the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_Chipset.zip Chipset driver] before the USB3.0 driver
* Download the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_USB30.zip USB3.0 driver]
+
# Download the [http://fit-iot.com/files/download/intense-pc2/sw/drivers/win7/IPC2_BDW_Win7_USB30.zip USB3.0 driver]
* Open the donloaded package
+
# Extract the downloaded package
* Run the '''OfflineSetup32.exe''' file for Windows 7 32bit or the '''OfflineSetup64.exe''' file for Windows 7 64bit
+
# Run the '''OfflineSetup32.exe''' file for Windows 7 32bit or the '''OfflineSetup64.exe''' file for Windows 7 64bit
* Follow the on-screen instructions
+
# Follow the on-screen instructions
* At the the end of installation process, reset the unit
+
# At the the end of installation process, reset the unit
* Enter the BIOS menu by pressing the '''F2''' key during the boot
+
# Enter the BIOS menu by pressing the '''[F2]''' key during boot
* Browse to the '''Advanced -> South Bridge Configuration -> SB USB Config''' menu and set the '''xHCI Mode''' setting to '''Enabled'''
+
# Browse to
* Press the '''F10''' key for Save&Exit
+
'''Advanced -> South Bridge Configuration -> SB USB Config''' Menu.
* When the Windwos boot up, open the donloaded package
+
    set the '''xHCI Mode''' setting to '''Enabled'''
* Run the '''Setup.exe''' file
+
# Press the '''[F10]''' key for Save&Exit
* Follow the on-screen instructions
+
# When Windows bootd up, open the downloaded package
* At the the end of installation process, reset the unit
+
# Run the '''Setup.exe''' file
 +
# Follow the on-screen instructions
 +
# At the the end of installation process, reset the unit
  
 
[[Category:IPC2]]
 
[[Category:IPC2]]
 
[[Category:software]]
 
[[Category:software]]
 
[[Category:Application notes]]
 
[[Category:Application notes]]

Revision as of 13:46, 15 October 2018

  • This application note provides a step by step guide to install USB3.0 drivers over Windows 7.
  • Applicable to IPC2-Broadwell machines.

Instructions

  1. Install the Chipset driver before the USB3.0 driver
  2. Download the USB3.0 driver
  3. Extract the downloaded package
  4. Run the OfflineSetup32.exe file for Windows 7 32bit or the OfflineSetup64.exe file for Windows 7 64bit
  5. Follow the on-screen instructions
  6. At the the end of installation process, reset the unit
  7. Enter the BIOS menu by pressing the [F2] key during boot
  8. Browse to
Advanced -> South Bridge Configuration -> SB USB Config Menu. 
   set the xHCI Mode setting to Enabled
  1. Press the [F10] key for Save&Exit
  2. When Windows bootd up, open the downloaded package
  3. Run the Setup.exe file
  4. Follow the on-screen instructions
  5. At the the end of installation process, reset the unit