Difference between revisions of "Quick AMT Setup"
From fit-PC wiki
(Created page with ''''Quick AMT Setup for IPC2, Intense PC and uSVR''' #Enter BIOS go to ADVANCED -> AMT Configuration and set "Enter Intel(R) MEBx Setup" to "Enabled" #Exit saving changes -> Syst...') (change visibility) |
|||
| Line 2: | Line 2: | ||
#Enter BIOS go to ADVANCED -> AMT Configuration and set "Enter Intel(R) MEBx Setup" to "Enabled" | #Enter BIOS go to ADVANCED -> AMT Configuration and set "Enter Intel(R) MEBx Setup" to "Enabled" | ||
| − | #Exit saving changes -> System will boot ( one time ) | + | #Exit saving changes -> System will boot ( one time ) to MEBx AMT setup |
#Enter "MEBx Login" -> using password "admin" and set the "Intel(R) ME New password " according with rules below | #Enter "MEBx Login" -> using password "admin" and set the "Intel(R) ME New password " according with rules below | ||
##At least 8 characters ( max32) | ##At least 8 characters ( max32) | ||
| Line 8: | Line 8: | ||
##At least one 7-bit ASCII non alpha-numeric character(e.g.'!','$',';') , but excluding ':' ,',' and '""' characters | ##At least one 7-bit ASCII non alpha-numeric character(e.g.'!','$',';') , but excluding ':' ,',' and '""' characters | ||
##At least one lower case letter ('a','b'...'z') and at least one upper case letter ('A' ,'B'...'Z') | ##At least one lower case letter ('a','b'...'z') and at least one upper case letter ('A' ,'B'...'Z') | ||
| − | #Enter "Intel(R) | + | #Enter "Intel(R) Standard Manageability Configuration" -> "Activate Network Access" and press "Y" |
#Enter "Network Setup" -> "TCP/IP Settings" ->"Wired LAN IPV4 Configuration" -> "DHCP Mode" and set to "Disabled" | #Enter "Network Setup" -> "TCP/IP Settings" ->"Wired LAN IPV4 Configuration" -> "DHCP Mode" and set to "Disabled" | ||
#Now set all IPs related settings and then press "ESC" four times - returning to main menu | #Now set all IPs related settings and then press "ESC" four times - returning to main menu | ||
| Line 15: | Line 15: | ||
'''Usage''' | '''Usage''' | ||
| − | #Connect Intel LAN to | + | #Connect Intel LAN 1 to a network |
#On the remote machine: | #On the remote machine: | ||
##Open browser and set address to http://your_ip:16992 when "your_ip" was set previously in the AMT setup | ##Open browser and set address to http://your_ip:16992 when "your_ip" was set previously in the AMT setup | ||
Revision as of 09:30, 7 February 2017
Quick AMT Setup for IPC2, Intense PC and uSVR
- Enter BIOS go to ADVANCED -> AMT Configuration and set "Enter Intel(R) MEBx Setup" to "Enabled"
- Exit saving changes -> System will boot ( one time ) to MEBx AMT setup
- Enter "MEBx Login" -> using password "admin" and set the "Intel(R) ME New password " according with rules below
- At least 8 characters ( max32)
- At least one digit character(0-9)
- At least one 7-bit ASCII non alpha-numeric character(e.g.'!','$',';') , but excluding ':' ,',' and '""' characters
- At least one lower case letter ('a','b'...'z') and at least one upper case letter ('A' ,'B'...'Z')
- Enter "Intel(R) Standard Manageability Configuration" -> "Activate Network Access" and press "Y"
- Enter "Network Setup" -> "TCP/IP Settings" ->"Wired LAN IPV4 Configuration" -> "DHCP Mode" and set to "Disabled"
- Now set all IPs related settings and then press "ESC" four times - returning to main menu
- Press "MEBx Exit" and wait until reboot
- Unplug your system for 20-30s and then plug it back
Usage
- Connect Intel LAN 1 to a network
- On the remote machine:
- Open browser and set address to http://your_ip:16992 when "your_ip" was set previously in the AMT setup
- Press "Log On" and enter login/password -> "admin"/your_psw when "your_psw" was set previously in the AMT setup
- Now all system information/status/remote management menus are accessible including remote power on/off
- For remote KVM use "VNC Viewer Plus": http://www.realvnc.com/products/viewerplus/
